Difference between revisions of "Group 4 - MAKE - Philip"
From Hackteria Wiki
(→DIY Chip) |
(→DIY Chip) |
||
Line 42: | Line 42: | ||
Step 1: Take a photosensitive laminated PCB card and draw or fix the PCB layout on the card. (black pen or printed transparent sheet) | Step 1: Take a photosensitive laminated PCB card and draw or fix the PCB layout on the card. (black pen or printed transparent sheet) | ||
+ | |||
+ | [[File:printed transparent sheet.jpg|400px]] | ||
Step 2: Place the board under the UV lamp for about 2 minutes or go outside and expose it to the sun (exposing time outside depends on the intensity of the sun) - Don`t leave it to long exposed! | Step 2: Place the board under the UV lamp for about 2 minutes or go outside and expose it to the sun (exposing time outside depends on the intensity of the sun) - Don`t leave it to long exposed! | ||
Line 52: | Line 54: | ||
The chip is now ready for soldering. | The chip is now ready for soldering. | ||
+ | |||
+ | [[File:prepared chip.jpg|400px]] | ||
Line 57: | Line 61: | ||
Step 1: Take the abrasive paper and sand the chip. | Step 1: Take the abrasive paper and sand the chip. | ||
+ | |||
+ | [[File:chip with abrasive paper.jpg|400px]] | ||
Step 2: Bend and shorten the edges of the semiconductor | Step 2: Bend and shorten the edges of the semiconductor | ||
Line 63: | Line 69: | ||
Step 4: Add the other components (ceramic capacitor, led light, speaker, battery connection) | Step 4: Add the other components (ceramic capacitor, led light, speaker, battery connection) | ||
+ | |||
+ | [[File:detailed chip.jpg|400px]] | ||
Step 5: Connect the battery and make noise :D | Step 5: Connect the battery and make noise :D | ||
+ | |||
+ | [[File:finished chip.jpg|400px]] | ||
Tipp: For a louder output use a 9V battery or connect the chip to an external speaker. | Tipp: For a louder output use a 9V battery or connect the chip to an external speaker. | ||
+ | |||
+ | [[File:chip with external speaker.jpg|400px]] |
Revision as of 17:26, 6 May 2015
Contents
DIY Chip
Text and pictures from BonsaiBob
You will need
Material
1. circuit board
2. semiconductor
3. ceramic caacitor
4. insulated wire
5. piezo speaker
6. led light
7. battery 3V/9V and battery connection
Tools
1. UV lamp
2. NaOH = developer, NaSO4 = caustic
3. abrasive paper
4. soldering bolt, solder
5. wire cutter
6. tweezers
Create a printed circuit board
Step 1: Take a photosensitive laminated PCB card and draw or fix the PCB layout on the card. (black pen or printed transparent sheet)
Step 2: Place the board under the UV lamp for about 2 minutes or go outside and expose it to the sun (exposing time outside depends on the intensity of the sun) - Don`t leave it to long exposed!
Step 3: Put it in a bath of acid (NaOH) - Stir every 2-3 minutes!
Step 4: Take it out, clean it with water and put it in a bath of NaSO4 - Stir every 3-5 minutes!
Step 5: Take it out and clean it again with water
The chip is now ready for soldering.
Connect components with the chip
Step 1: Take the abrasive paper and sand the chip.
Step 2: Bend and shorten the edges of the semiconductor
Step 3: Connect the semiconductor onto the chip - !Watch the direction of the semiconductor!
Step 4: Add the other components (ceramic capacitor, led light, speaker, battery connection)
Step 5: Connect the battery and make noise :D
Tipp: For a louder output use a 9V battery or connect the chip to an external speaker.