Difference between revisions of "Team Mentorzzzz"

From Hackteria Wiki
Jump to: navigation, search
 
(21 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
'''Yeah we have our own wiki page!!!'''
 
'''Yeah we have our own wiki page!!!'''
  
[[File:Onyx_ashanti_face.jpg|right|400px]]
+
let go back to [[Medizintechnik DIY]]
  
let go back to [[Medizintechnik DIY]]
+
== Sync HeartBeat to KORG Volca ==
 +
 
 +
[[File:HeartBeat_serialOutput.png|thumb|left|400px|Checking the signals in Serial Plotter of Arduino IDE]]
 +
<br clear=all>
 +
Gaudi edited the main Heart beat Code, Spike Recoreder V1.1 to have an output LED HIGH on Pin 12, when a 80% gliding max threshold is reached.
  
 +
https://gist.github.com/dusjagr/73773c650bf341842f70b08953fae009
  
 +
[[File:Heart_to_KORG-sync.jpg|thumb|left|400px|Hallo]]
 +
<br clear=all>
 +
Just connect the KORG Sync-In with the BYB cable to your shield and there you go, the TEMPO of the synthesizer is controlled by your heartbeat. Each beat will be followed by 2 steps on the KORG, which is typical to allow swing and other sub-step rythms.
  
 +
== Hacking the PulseOximeter ==
  
 +
[[File:Pulsoxy_hacking_legend.png|640px]]
 +
<br clear=all>
 +
Can we just hack a cheap Finger Pulse oximeter, to send out the heartbeat as CV or SYNC to a synth? ordered a few from ebay below 10$ and opening them up.
  
 +
<gallery mode="packed-hover" widths=320px heights=200px>
 +
File:Pulsoxymeter_01_openingUp.jpg|Easy to open from the front with a sharp knife and CLICK
 +
File:Pulsoxymeter_02_flatband.jpg|Be careful, that thin flatband wire keeps breaking of, but can be fixed if your soldering skills are ok
 +
File:Pulsoxymeter_03_ReverseEngineering.jpg|Looking at the circuit, ICs and other stuff on the board
 +
File:Pulsoxymeter_04_BackLED.jpg|In the lower part there is only the 2 x AAA batteries and a red LED
 +
File:Pulsoxymeter_05_redFinger.jpg|Measurement concept is simple. The LED shines through your finger
 +
File:Pulsoxymeter_06_detachedSensor.jpg|Soldered long wires on the LED and the photosensor to be able to only place those onto the finger
 +
</gallery>
  
 
[[Category:MedTech-DIY]]
 
[[Category:MedTech-DIY]]

Latest revision as of 11:34, 15 February 2019

Yeah we have our own wiki page!!!

let go back to Medizintechnik DIY

Sync HeartBeat to KORG Volca

Checking the signals in Serial Plotter of Arduino IDE


Gaudi edited the main Heart beat Code, Spike Recoreder V1.1 to have an output LED HIGH on Pin 12, when a 80% gliding max threshold is reached.

https://gist.github.com/dusjagr/73773c650bf341842f70b08953fae009

Hallo


Just connect the KORG Sync-In with the BYB cable to your shield and there you go, the TEMPO of the synthesizer is controlled by your heartbeat. Each beat will be followed by 2 steps on the KORG, which is typical to allow swing and other sub-step rythms.

Hacking the PulseOximeter

Pulsoxy hacking legend.png
Can we just hack a cheap Finger Pulse oximeter, to send out the heartbeat as CV or SYNC to a synth? ordered a few from ebay below 10$ and opening them up.