Difference between revisions of "Jurus Sulam Listrik workshop 2022"

From Hackteria Wiki
Jump to: navigation, search
m (Materials)
m (Materials)
Line 6: Line 6:
 
== Materials ==
 
== Materials ==
 
Tweezers
 
Tweezers
 +
 
resistors 22
 
resistors 22
 +
 
resistor 102
 
resistor 102
 +
 
Piezo  
 
Piezo  
 +
 
3.5 audio terminal  
 
3.5 audio terminal  
 +
 
Coin battery 3V
 
Coin battery 3V
 +
 
Battery holder
 
Battery holder
 +
 
Embroidery Needle
 
Embroidery Needle
 +
 
Embroidery frame  
 
Embroidery frame  
Capacitor nf
+
 
 +
Capacitor 100 nf
 +
 
 
EMF tape
 
EMF tape
 +
 
Attiny85
 
Attiny85
 +
 
soldering gun
 
soldering gun
 +
 
[https://www.amazon.com/Count-Embroidery-Counted-Stitch-Fabric/dp/B09B5VNJKW cross stitch canvas 22 ct]
 
[https://www.amazon.com/Count-Embroidery-Counted-Stitch-Fabric/dp/B09B5VNJKW cross stitch canvas 22 ct]
  

Revision as of 10:54, 1 July 2022

Jurus Sulam Listrik Workshop Lifepatch 2022 July

Abstract

This workshop introduce the technique that Shih Wei Chieh employs it in his e-textile work "I am Very Happy I Hope You are too" in his residency program in Oaxaca, Mexico 2013. The purpose was to allow, encourage untrained engineer, local aztec villager to participate circuits manufacturing with craft skill they are familiar with such as embroidery technique, stitching, weaving. In this workshop you will be introduced how to manufacture circuits with embroidery threads and conductive threads, assemble LEDs with sewing instead of soldering. However the smd components still require soldering. The circuits in this workshop we will using is from "Mixed Tape", which is an audio programmable Attiny85 circuit. Attiny85 is a micro Arduino chip which allowed you to do several task, it enables you to do several jobs like LED blinks, motor movements or sensor readings etc.

Materials

Tweezers

resistors 22

resistor 102

Piezo

3.5 audio terminal

Coin battery 3V

Battery holder

Embroidery Needle

Embroidery frame

Capacitor 100 nf

EMF tape

Attiny85

soldering gun

cross stitch canvas 22 ct

The Embroidered 8 bits Mixtape Synth circuit

We will use the audio input part from the 8bit Mixtape synth NEO schematic for the embroidered circuit making. For the embroidery we will use the conventional embroidery canvas for cross stitch in 22 ct specs. 22 ct means 22 holes within one inch, therefore it is exactly same gap between SMD pins, 1.27 mm, so it perfectly simulate the PDB environment. However it is only my preference and I like the aesthetic, you may of course embroider with any kind of fabric.

steps

  1. You can draw the circuit sketch on the embroidery canvas for your own schematic design, in theory you can make very fun pattern freely as long as the connections are all correct, or you can just make a very minimum circuit layout with shortest path like conventional PCB layout assignment. However it is recommended that you should leave some minimum distant between each component so it will be easier for the sewing work.
  2. We need to solder some conductive threads onto each pins of the electronic components for the later embroidery sewing work.
  3. Sewing up the component first, and then the connections. For the connections we don't use soldering either, we simply join the conductive threads by overlapping two threads together and then wrap it with embroidery threads with some pressure, so it can be conducted.

The LEDs assembling

The soldering is flexible circuits enemy! we always want to avoid soldering in any circumstance if you try to make a flexible circuits or wearable crafts. Of course it is impossible to avoid all the soldering but we try our best. Here we are using a special type of Top LED from Osram. It was two wings in ∫ shape, we can clamp it with tweezer so the LED can be attached with the conductive threads.


Prototypes and the finish works

Examples of the embroidered circuits and LEDs arrays.

References