Difference between revisions of "DIY Microscopy Instruction (Japanese)"

From Hackteria Wiki
Jump to: navigation, search
(1. ウェブカメラの改造 パートB: 顕微鏡に改造)
(1. ウェブカメラの改造 パートB: 顕微鏡に改造)
Line 83: Line 83:
 
* ウェブカメラ内部:カメラの眼になるセンサー、エレクトロニクスのスイッチ。照明用LEDは別に後から取り付けるので元のLEDは必要ない。
 
* ウェブカメラ内部:カメラの眼になるセンサー、エレクトロニクスのスイッチ。照明用LEDは別に後から取り付けるので元のLEDは必要ない。
 
* レンスは接着剤で取り付けてあるので、気をつけてエレクトロニクスから取り外す。レンズの外側に付いている輪カバー(写真右)は使わない。
 
* レンスは接着剤で取り付けてあるので、気をつけてエレクトロニクスから取り外す。レンズの外側に付いている輪カバー(写真右)は使わない。
* With the use of a strong side cutter we cut through the plastic casing. Now the electronics including all wires and the USB cable can be removed from the casing.
+
* カッターなどを使い、銅線、USBケーブルは切らないで残しカメラ後ろのプラスチックケースを取り除く。エレクトロニクス、ケーブル全てが放たれる。
* The webcam’s interior: on the left side of the picture we can see the internal microphone, which, however, is not needed for our project.
+
* ウェブカメラ内部:The webcam’s interior: on the left side of the picture we can see the internal microphone, which, however, is not needed for our project.
 
* Now we place the optics upside down on the fitting. It can no longer be screwed on and must therefore be firmly secured. The optics is attached with a piece of duct tape.
 
* Now we place the optics upside down on the fitting. It can no longer be screwed on and must therefore be firmly secured. The optics is attached with a piece of duct tape.
 
* To test the equipment we connect the modified webcam with the computer and point the lens towards the screen. Now the individual
 
* To test the equipment we connect the modified webcam with the computer and point the lens towards the screen. Now the individual

Revision as of 14:17, 28 December 2015

Instructions to be translated

[[File:hackteria-mikroskop-2012-137.JPG|right|400px|thumb|The Chapter about the DIY microscope can be downloaded here and available now with Chinese translation included!

Would be great to have this also in other languages, below is the english original to get you started.

Translations

DIY Mikroskop Anleitung (Deutsch)

DIY Microscopy Instruction (Chinese)

DIY Microscopy Instruction (Spanish)

DIY Microscopy Instruction (Bahasa Indonesia)

DIY Microscopy Instruction (French)

DIY Microscopy Instruction (Japanese)

0. はじめに

ハクテリアのDIY顕微鏡工作のコンセプトは誰にでもできる市販のウェブカメラの改造です。ウェブカメラのエレクトロニクスはノータッチで、レンズの位置を変えるだけ。その上に、安定したスタンドを作り、LEDライトでサンプルを照明します。

DIY顕微鏡製作三段階

  • ウェブカメラの改造
  • スタンド作り
  • 発行ダイオード light-emitting diode (LED)の照明

用意するものリスト

DIY-Microscope Instructions Materials.png

材料

  • 1 ウェブカメラ
  • 厚めのダンボール / 工作用 木材 20 x 30 cm
  • スチレンボード 20 x 30 cm
  • M4 ネジ 長さ約 15 mm とボルト
  • ダクトテープ
  • 粘着ゴム
  • ホットメルトグルーガン用のグルーステイック
  • 輪ゴム

道具

  • カッター
  • ねじ回し
  • ホットメルトグルーガン
  • (オプション) はんだごて

オプション、外部LED照明光源

  • 1 スイッチ
  • 1 白 LED
  • 1 電池 (9V)
  • 1 ケーブル付き バッテリーホルダー
  • 1 抵抗 レジスタ (1 k Ω )
  • 1 ポテンショメーター (20 k Ω )
  • 30 cm 絶縁線
  • 針金

顕微鏡分析、微生物観察 用具

  • 透明なプラスチックカップ
  • スライドガラス
  • ペトリ皿 プラスチック、又はガラス
  • ピペット
  • 油性ペン
  • 小さじ
  • ピンセット
  • サンプル用小さいプラスチック容器

1. ウェブカメラの改造 パートA: 小さい世界の拡大

Step 1 get stuff.jpg

  • 市販のウェブカメラの色々。レンズのマニュアルフォーカスできるウェブカメラモデルがDIY顕微鏡用に適している。 トライアンドエラーで好きなモデルを決めよう。
  • ウェブカメラの改造前にコンピューターに繋げ、ウェブカメラが作用するかを試そう(ドライバーのインストールなど)。Windows, Mac, or Linux.

Step 2 screw lens outwards.jpg

  • この時点でウェブカメラを使い身の回りの世界を拡大してみる。レンズのネジを緩め、ポケットランプなどでサンプルを照らし、観察したいサンプルに近づいてみよう。
  • ウェブカメラを改造しなくても肉眼で見えない世界が見えて来る。

1. ウェブカメラの改造 パートB: 顕微鏡に改造

Step 3 invert lens.jpg

  • ウェブカメラの解体を始める。見えるねじ、そしてラベルやゴムの下に隠れているねじを全て取り除く。しっかりとした道具、例えばねじ回し、スイスアーミーナイフ(写真)でウェブカメラのカバー本体をこじ開ける。
  • ウェブカメラ内部:カメラの眼になるセンサー、エレクトロニクスのスイッチ。照明用LEDは別に後から取り付けるので元のLEDは必要ない。
  • レンスは接着剤で取り付けてあるので、気をつけてエレクトロニクスから取り外す。レンズの外側に付いている輪カバー(写真右)は使わない。
  • カッターなどを使い、銅線、USBケーブルは切らないで残しカメラ後ろのプラスチックケースを取り除く。エレクトロニクス、ケーブル全てが放たれる。
  • ウェブカメラ内部:The webcam’s interior: on the left side of the picture we can see the internal microphone, which, however, is not needed for our project.
  • Now we place the optics upside down on the fitting. It can no longer be screwed on and must therefore be firmly secured. The optics is attached with a piece of duct tape.
  • To test the equipment we connect the modified webcam with the computer and point the lens towards the screen. Now the individual

RGB pixels on screen become visible.

2. Construction of the platform

Step 4 make stage.jpg

  • Using small lumps of Blu-Tack adhesive, the webcam is attached to a solid pasteboard of about 15 x 15 cm.
  • The platform’s side wall consisting of scale model cardboard. With a pencil we draw the height of the lens on it and cut off the cardboard along that line. We use hot glue for pasting.
  • Using a carpet cutter, we cut a rectangular opening into another piece of scale model cardboard. This piece too is attached with hot glue.

Step 5 adjustable focus.jpg

  • The adjustable screw requires a hole. We attach the screw nut right at the top with a small drop of hot glue. Then we insert the adjustable screw. It must reach down to the lower platform.
  • Rubber bands provide more stability to the platform. With the screw the scale model board can now be moved up and down by a few millimeters.

3. The light source

Step 6 add ligthing.jpg

  • Our microscope also has a light source in the form of a light-emitting diode (LED). The lighting can be easily produced by oneself.
  • In this easy way, the wires can be twisted together. But it is safer if they are solded on.
  • The centimeters long feed of our light source is wrapped with garden wire. The wire thus becomes pliable and later can be attached in any position.
  • The light source, potentiometer and battery are attached to our construction with hot glue. Our DIY MICROSCOPE is ready for use.

3.B Hacking the LEDs from the Webcam (to be documented)

  • Coming soon

4. Using the Microscope and Hunting for Microorganisms

Step 7 go hunting.jpg

  • The USB cable of the converted webcam is connected to the computer. Now we can begin with our examinations.
  • The study objects are placed on a glass slide and can be shifted by hand. The microscope’s focus is regulated by the adjustable screw.
  • As with a professional microscope, with our DIY tool we are able to take electronic photos and even films. Photos and films are digitally available, can be further processed and of course be easily published on the Internet.