Difference between revisions of "Team Mentorzzzz"
From Hackteria Wiki
(→Hacking the PulsOxymeter) |
|||
(6 intermediate revisions by the same user not shown) | |||
Line 15: | Line 15: | ||
Just connect the KORG Sync-In with the BYB cable to your shield and there you go, the TEMPO of the synthesizer is controlled by your heartbeat. Each beat will be followed by 2 steps on the KORG, which is typical to allow swing and other sub-step rythms. | Just connect the KORG Sync-In with the BYB cable to your shield and there you go, the TEMPO of the synthesizer is controlled by your heartbeat. Each beat will be followed by 2 steps on the KORG, which is typical to allow swing and other sub-step rythms. | ||
− | == Hacking the | + | == Hacking the PulseOximeter == |
− | [[File: | + | |
+ | [[File:Pulsoxy_hacking_legend.png|640px]] | ||
+ | <br clear=all> | ||
+ | Can we just hack a cheap Finger Pulse oximeter, to send out the heartbeat as CV or SYNC to a synth? ordered a few from ebay below 10$ and opening them up. | ||
<gallery mode="packed-hover" widths=320px heights=200px> | <gallery mode="packed-hover" widths=320px heights=200px> | ||
− | File:Pulsoxymeter_01_openingUp.jpg | + | File:Pulsoxymeter_01_openingUp.jpg|Easy to open from the front with a sharp knife and CLICK |
− | File:Pulsoxymeter_02_flatband.jpg | + | File:Pulsoxymeter_02_flatband.jpg|Be careful, that thin flatband wire keeps breaking of, but can be fixed if your soldering skills are ok |
− | File:Pulsoxymeter_03_ReverseEngineering.jpg | + | File:Pulsoxymeter_03_ReverseEngineering.jpg|Looking at the circuit, ICs and other stuff on the board |
− | File:Pulsoxymeter_04_BackLED.jpg | + | File:Pulsoxymeter_04_BackLED.jpg|In the lower part there is only the 2 x AAA batteries and a red LED |
− | File:Pulsoxymeter_05_redFinger.jpg | + | File:Pulsoxymeter_05_redFinger.jpg|Measurement concept is simple. The LED shines through your finger |
− | File:Pulsoxymeter_06_detachedSensor.jpg | + | File:Pulsoxymeter_06_detachedSensor.jpg|Soldered long wires on the LED and the photosensor to be able to only place those onto the finger |
</gallery> | </gallery> | ||
[[Category:MedTech-DIY]] | [[Category:MedTech-DIY]] |
Latest revision as of 12:34, 15 February 2019
Yeah we have our own wiki page!!!
let go back to Medizintechnik DIY
Sync HeartBeat to KORG Volca
Gaudi edited the main Heart beat Code, Spike Recoreder V1.1 to have an output LED HIGH on Pin 12, when a 80% gliding max threshold is reached.
https://gist.github.com/dusjagr/73773c650bf341842f70b08953fae009
Just connect the KORG Sync-In with the BYB cable to your shield and there you go, the TEMPO of the synthesizer is controlled by your heartbeat. Each beat will be followed by 2 steps on the KORG, which is typical to allow swing and other sub-step rythms.
Hacking the PulseOximeter
Can we just hack a cheap Finger Pulse oximeter, to send out the heartbeat as CV or SYNC to a synth? ordered a few from ebay below 10$ and opening them up.