Difference between revisions of "PDA-100 Photodiode Array Spectrometer Hack"
(Created page with " Deuterium and Tungsten Lamp Power Supply ASSY 062800 MAX500 DAC: VOUT-A (Pin 2): High Voltage Level VOUT-B (Pin 1): D2 Fil Voltage (Preheat Current) VOUT-C (Pin 16): Thungs...") |
|||
Line 1: | Line 1: | ||
− | + | <br> | |
− | Deuterium and Tungsten Lamp Power Supply | + | Deuterium and Tungsten Lamp Power Supply<br> |
− | ASSY 062800 | + | ASSY 062800<br> |
− | + | <br><br> | |
− | MAX500 DAC: | + | MAX500 DAC:<br> |
− | + | <br> | |
− | VOUT-A (Pin 2): High Voltage Level | + | VOUT-A (Pin 2): High Voltage Level<br> |
− | VOUT-B (Pin 1): D2 Fil Voltage (Preheat Current) | + | VOUT-B (Pin 1): D2 Fil Voltage (Preheat Current)<br> |
− | VOUT-C (Pin 16): Thungsten Lamp Intensity | + | VOUT-C (Pin 16): Thungsten Lamp Intensity<br> |
− | VOUT-D (Pin 15): Set Teperature | + | VOUT-D (Pin 15): Set Teperature<br> |
− | + | <br> | |
− | 20 Pin connector: | + | 20 Pin connector:<br> |
− | (probably mostly feedback, no details yet): | + | (probably mostly feedback, no details yet):<br> |
− | Pin 1 | + | Pin 1<br> |
− | Pin 2: DAC | + | Pin 2: DAC<br> |
− | Pin 3 | + | Pin 3<br> |
− | Pin 4 | + | Pin 4<br> |
− | Pin 5 | + | Pin 5<br> |
− | Pin 6: R52 | + | Pin 6: R52<br> |
− | Pin 7: (5V?) | + | Pin 7: (5V?)<br> |
− | Pin 8: GND | + | Pin 8: GND<br> |
− | Pin 9: | + | Pin 9:<br> |
− | Pin 10: goes to many resistors | + | Pin 10: goes to many resistors <br> |
− | Pin 11: (5V?) | + | Pin 11: (5V?)<br> |
− | Pin 12: Clock for HV | + | Pin 12: Clock for HV<br> |
− | Pin 13: | + | Pin 13: <br> |
− | Pin 14: DAC | + | Pin 14: DAC<br> |
− | Pin 15: R? | + | Pin 15: R?<br> |
− | Pin 16: R? Temp something | + | Pin 16: R? Temp something<br> |
− | Pin 17: | + | Pin 17: <br> |
− | Pin 18: | + | Pin 18: <br> |
− | Pin 19: | + | Pin 19:<br> |
− | Pin 20: R54 | + | Pin 20: R54<br> |
− | + | <br> | |
− | To power the lamps: | + | To power the lamps:<br> |
− | Pin 12 needs to powered with a CLOCK signal for the High Voltage transformer. Don't know the exact frequency (can someone measure, please?). Works for me with 20KHz. | + | Pin 12 needs to powered with a CLOCK signal for the High Voltage transformer. Don't know the exact frequency (can someone measure, please?). Works for me with 20KHz.<br> |
− | + | <br> | |
− | Sequence to power the Deuterium: Set high voltage to about 25% (4V), LED NO/F lights up. Then turn "D2 Fil" up until NO/F light goes off, ignition flash, D/OK should light green. Then turn D2 Fil down to zero again. | + | Sequence to power the Deuterium: Set high voltage to about 25% (4V), LED NO/F lights up. Then turn "D2 Fil" up until NO/F light goes off, ignition flash, D/OK should light green. Then turn D2 Fil down to zero again.<br> |
Revision as of 18:50, 2 July 2020
Deuterium and Tungsten Lamp Power Supply
ASSY 062800
MAX500 DAC:
VOUT-A (Pin 2): High Voltage Level
VOUT-B (Pin 1): D2 Fil Voltage (Preheat Current)
VOUT-C (Pin 16): Thungsten Lamp Intensity
VOUT-D (Pin 15): Set Teperature
20 Pin connector:
(probably mostly feedback, no details yet):
Pin 1
Pin 2: DAC
Pin 3
Pin 4
Pin 5
Pin 6: R52
Pin 7: (5V?)
Pin 8: GND
Pin 9:
Pin 10: goes to many resistors
Pin 11: (5V?)
Pin 12: Clock for HV
Pin 13:
Pin 14: DAC
Pin 15: R?
Pin 16: R? Temp something
Pin 17:
Pin 18:
Pin 19:
Pin 20: R54
To power the lamps:
Pin 12 needs to powered with a CLOCK signal for the High Voltage transformer. Don't know the exact frequency (can someone measure, please?). Works for me with 20KHz.
Sequence to power the Deuterium: Set high voltage to about 25% (4V), LED NO/F lights up. Then turn "D2 Fil" up until NO/F light goes off, ignition flash, D/OK should light green. Then turn D2 Fil down to zero again.